Sanigrey and traditional greywater drainage: Which solution should you choose for kitchens and laundry areas?

Sanigrey or traditional greywater drainage for kitchens and laundry areas? Compare installation, layout flexibility, operation and maintenance to choose the right solution.

Did you know?|

5 min read

||

Published on 11/11/2026

cs

When relocating a sink, adding a laundry area or moving a pantry, the usual approach is to connect the new location to the building’s gravity-based greywater drainage system. This traditional installation requires a suitable pipe route, the right slope and a convenient connection point. If these conditions are not available, the project may require floor breaking, longer pipe runs or floor raising. However, Sanigrey offers another approach by collecting wastewater at the installation point and pumping it to the existing drainage system. So how do the two solutions differ, and when should each one be considered?

 

Key highlights

  • Background: Relocating a sink, adding a laundry area or moving a pantry to a location without an existing drainage connection.
  • Challenge: The traditional approach may require floor breaking, additional pipework and floor raising to create the required slope.
  • Solution: Sanigrey collects wastewater on site and pumps it through a discharge pipe to the existing drainage system.
  • Result: Sanigrey expands the possibilities for placing sinks, laundry areas and pantries where gravity drainage connections are difficult, without complex construction work.

 

Challenges 

Relocating a sink, laundry area or pantry to a new location without an existing drainage connection can create several challenges during renovation. Connecting the new location to the existing system may require floor breaking to install new pipes or floor raising to create the required slope.

In kitchen areas, long pipe runs can also allow grease to build up. This may increase the risk of blockages and make cleaning and maintenance more difficult. As a result, the project needs to consider both the level of construction work required and the long-term cleaning and maintenance of the system.

 

Traditional greywater drainage

With traditional greywater drainage, wastewater from a sink or washing machine flows through pipes to the existing drainage system by gravity. When the new location is far from the connection point, the pipe route must be installed with the appropriate slope. The project may require floor or wall breaking, or floor raising to create the required level.

This approach is suitable when the building has enough technical space and the pipe route can be installed conveniently. However, in kitchen areas, long pipe runs or multiple changes in direction can allow grease to build up. This can make the system more difficult to inspect, clean and maintain over time.

 

The Sanigrey solution: collects wastewater on site and pumps it to the existing system

Sanigrey addresses the drainage challenge by placing a pump at the location of the sink, washing machine or other water-using appliance. Depending on the model and installation conditions, the unit can be installed neatly beneath the kitchen sink or close to the appliance. Sanigrey collects the wastewater and pumps it through a small discharge pipe to the building’s drainage system.

Because the pump generates the force needed to move the wastewater, the flow does not have to rely entirely on gravity through a long pipe route. This allows water-using appliances to be connected to the building’s drainage system even when the new installation point does not have a nearby drainage connection.

Sanivite can handle hot water up to 60°C, making it suitable for areas where warm or hot water is generated within the product’s operating range. In restaurant kitchens or areas with high grease levels, a grease trap should be installed before the pump to reduce the amount of grease entering the unit and the discharge pipe.

You can learn more about the Sanigrey range for kitchens and laundry areas and Sanivite.

 

Comparing Sanigrey with traditional greywater drainage

The main difference lies in how wastewater is moved to the connection point. Sanigrey collects wastewater at the installation point and pumps it through a discharge pipe selected according to the model, while the traditional approach relies on gravity, pipe slope and a pipe route designed for natural flow.

Criteria

Sanigrey

Traditional greywater drainage

Installation process

Install the pump near the appliance, collect wastewater on site and pump it through a small discharge pipe to the connection point.

Run a pipe from the sink, washing machine or other appliance to the connection point while creating the required slope.

Installation time

Usually completed within a few hours, mainly involving pump installation, discharge pipe connection and connection to the receiving point. Actual time depends on the model and site conditions.

May take longer because of pipe installation, slope creation, floor or wall breaking and reinstatement work.

Layout flexibility

Allows sinks, washing machines and pantries to be installed more flexibly, including at locations without a nearby drainage connection. Depending on the model, the pump can be installed beneath the sink or inside a cabinet.

Appliance locations are limited by the existing drainage pipes, available slope and space required for the pipe route.

Cleaning and maintenance

The unit is installed close to the point of use, making access, inspection and cleaning more convenient.

Long pipe runs or multiple changes in direction can make access, inspection and cleaning more difficult.

 

Operating and maintaining Sanigrey

Sanigrey should be used with the appropriate type of wastewater and connected appliances for each model. In restaurant kitchens or areas with high grease levels, a grease trap should be installed before the pump and cleaned regularly to reduce the amount of grease entering the unit and discharge pipe.

For stable operation, users should:

  • Avoid discharging solid objects or unsuitable substances into the system.
  • Clean the grease trap at suitable intervals.
  • Check the discharge pipe and connection point when unusual signs appear.
  • Follow the product’s installation and maintenance instructions.
  • Select the model according to the wastewater type and connected appliance.
  • Keep the unit accessible for inspection and maintenance.

Stable operation depends on the equipment, wastewater type and daily usage. In kitchen areas, controlling grease before it enters the pump is especially important.

 

Conclusion

Traditional greywater drainage is suitable when the building has enough space to create the required slope, install the pipe route and connect to a convenient receiving point. Sanigrey is a suitable option to consider when sinks, laundry areas or pantries need to be relocated or added in areas where gravity drainage is difficult.

The right choice depends not only on how wastewater is moved, but also on the installation process, project timeline, layout flexibility, water temperature, cleaning and maintenance requirements. If you need advice on Sanigrey for a kitchen, laundry area or pantry, please contact SFA Pumps .

FAQs

Any questions ?

  • Traditional greywater drainage moves wastewater through pipes by gravity. Sanigrey collects wastewater at the installation point and pumps it to the existing drainage system.

  • Gravity drainage is suitable when the building can accommodate a sloped pipe route and has a convenient connection point. If the building is already completed or creating a slope is difficult, Sanigrey can be considered.

  • Depending on the model and installation conditions, Sanigrey can be installed beneath a sink, inside a cabinet or near the water-using appliance.

  • Yes. For wastewater containing high levels of grease, especially in restaurants, a grease trap should be installed before the pump to reduce grease entering the unit and discharge pipe.

  • Sanivite can handle hot water up to 60°C. For other Sanigrey models, the permitted wastewater temperature depends on the characteristics of each model.

  • Traditional greywater drainage moves wastewater through pipes by gravity. Sanigrey collects wastewater at the installation point and pumps it to the existing drainage system.

  • Yes. For wastewater containing high levels of grease, especially in restaurants, a grease trap should be installed before the pump to reduce grease entering the unit and discharge pipe.

  • Gravity drainage is suitable when the building can accommodate a sloped pipe route and has a convenient connection point. If the building is already completed or creating a slope is difficult, Sanigrey can be considered.

  • Sanivite can handle hot water up to 60°C. For other Sanigrey models, the permitted wastewater temperature depends on the characteristics of each model.

  • Depending on the model and installation conditions, Sanigrey can be installed beneath a sink, inside a cabinet or near the water-using appliance.